Sync with linux/nl80211.h from wireless-testing.git

src/drivers/nl80211_copy.h

@@ -76,6 +76,39 @@
  * below.
  */
 
+/**
+ * DOC: Virtual interface / concurrency capabilities
+ *
+ * Some devices are able to operate with virtual MACs, they can have
+ * more than one virtual interface. The capability handling for this
+ * is a bit complex though, as there may be a number of restrictions
+ * on the types of concurrency that are supported.
+ *
+ * To start with, each device supports the interface types listed in
+ * the %NL80211_ATTR_SUPPORTED_IFTYPES attribute, but by listing the
+ * types there no concurrency is implied.
+ *
+ * Once concurrency is desired, more attributes must be observed:
+ * To start with, since some interface types are purely managed in
+ * software, like the AP-VLAN type in mac80211 for example, there's
+ * an additional list of these, they can be added at any time and
+ * are only restricted by some semantic restrictions (e.g. AP-VLAN
+ * cannot be added without a corresponding AP interface). This list
+ * is exported in the %NL80211_ATTR_SOFTWARE_IFTYPES attribute.
+ *
+ * Further, the list of supported combinations is exported. This is
+ * in the %NL80211_ATTR_INTERFACE_COMBINATIONS attribute. Basically,
+ * it exports a list of "groups", and at any point in time the
+ * interfaces that are currently active must fall into any one of
+ * the advertised groups. Within each group, there are restrictions
+ * on the number of interfaces of different types that are supported
+ * and also the number of different channels, along with potentially
+ * some other restrictions. See &enum nl80211_if_combination_attrs.
+ *
+ * All together, these attributes define the concurrency of virtual
+ * interfaces that a given device supports.
+ */
+
 /**
  * enum nl80211_commands - supported nl80211 commands
  *
@@ -148,6 +181,10 @@
  * @NL80211_CMD_SET_MPATH:  Set mesh path attributes for mesh path to
  * 	destination %NL80211_ATTR_MAC on the interface identified by
  * 	%NL80211_ATTR_IFINDEX.
+ * @NL80211_CMD_NEW_MPATH: Create a new mesh path for the destination given by
+ *	%NL80211_ATTR_MAC via %NL80211_ATTR_MPATH_NEXT_HOP.
+ * @NL80211_CMD_DEL_MPATH: Delete a mesh path to the destination given by
+ *	%NL80211_ATTR_MAC.
  * @NL80211_CMD_NEW_PATH: Add a mesh path with given attributes to the
  *	the interface identified by %NL80211_ATTR_IFINDEX.
  * @NL80211_CMD_DEL_PATH: Remove a mesh path identified by %NL80211_ATTR_MAC
@@ -172,10 +209,10 @@
  * 	to the specified ISO/IEC 3166-1 alpha2 country code. The core will
  * 	store this as a valid request and then query userspace for it.
  *
- * @NL80211_CMD_GET_MESH_PARAMS: Get mesh networking properties for the
+ * @NL80211_CMD_GET_MESH_CONFIG: Get mesh networking properties for the
  *	interface identified by %NL80211_ATTR_IFINDEX
  *
- * @NL80211_CMD_SET_MESH_PARAMS: Set mesh networking properties for the
+ * @NL80211_CMD_SET_MESH_CONFIG: Set mesh networking properties for the
  *      interface identified by %NL80211_ATTR_IFINDEX
  *
  * @NL80211_CMD_SET_MGMT_EXTRA_IE: Set extra IEs for management frames. The
@@ -199,6 +236,29 @@
  * @NL80211_CMD_SCAN_ABORTED: scan was aborted, for unspecified reasons,
  *	partial scan results may be available
  *
+ * @NL80211_CMD_START_SCHED_SCAN: start a scheduled scan at certain
+ *	intervals, as specified by %NL80211_ATTR_SCHED_SCAN_INTERVAL.
+ *	Like with normal scans, if SSIDs (%NL80211_ATTR_SCAN_SSIDS)
+ *	are passed, they are used in the probe requests.  For
+ *	broadcast, a broadcast SSID must be passed (ie. an empty
+ *	string).  If no SSID is passed, no probe requests are sent and
+ *	a passive scan is performed.  %NL80211_ATTR_SCAN_FREQUENCIES,
+ *	if passed, define which channels should be scanned; if not
+ *	passed, all channels allowed for the current regulatory domain
+ *	are used.  Extra IEs can also be passed from the userspace by
+ *	using the %NL80211_ATTR_IE attribute.
+ * @NL80211_CMD_STOP_SCHED_SCAN: stop a scheduled scan.  Returns -ENOENT
+ *	if scheduled scan is not running.
+ * @NL80211_CMD_SCHED_SCAN_RESULTS: indicates that there are scheduled scan
+ *	results available.
+ * @NL80211_CMD_SCHED_SCAN_STOPPED: indicates that the scheduled scan has
+ *	stopped.  The driver may issue this event at any time during a
+ *	scheduled scan.  One reason for stopping the scan is if the hardware
+ *	does not support starting an association or a normal scan while running
+ *	a scheduled scan.  This event is also sent when the
+ *	%NL80211_CMD_STOP_SCHED_SCAN command is received or when the interface
+ *	is brought down while a scheduled scan was running.
+ *
  * @NL80211_CMD_GET_SURVEY: get survey resuls, e.g. channel occupation
  *      or noise level
  * @NL80211_CMD_NEW_SURVEY_RESULTS: survey data notification (as a reply to
@@ -406,11 +466,37 @@
  *	notification. This event is used to indicate that an unprotected
  *	disassociation frame was dropped when MFP is in use.
  *
+ * @NL80211_CMD_NEW_PEER_CANDIDATE: Notification on the reception of a
+ *      beacon or probe response from a compatible mesh peer.  This is only
+ *      sent while no station information (sta_info) exists for the new peer
+ *      candidate and when @NL80211_MESH_SETUP_USERSPACE_AUTH is set.  On
+ *      reception of this notification, userspace may decide to create a new
+ *      station (@NL80211_CMD_NEW_STATION).  To stop this notification from
+ *      reoccurring, the userspace authentication daemon may want to create the
+ *      new station with the AUTHENTICATED flag unset and maybe change it later
+ *      depending on the authentication result.
+ *
+ * @NL80211_CMD_GET_WOWLAN: get Wake-on-Wireless-LAN (WoWLAN) settings.
+ * @NL80211_CMD_SET_WOWLAN: set Wake-on-Wireless-LAN (WoWLAN) settings.
+ *	Since wireless is more complex than wired ethernet, it supports
+ *	various triggers. These triggers can be configured through this
+ *	command with the %NL80211_ATTR_WOWLAN_TRIGGERS attribute. For
+ *	more background information, see
+ *	http://wireless.kernel.org/en/users/Documentation/WoWLAN.
+ *
+ * @NL80211_CMD_SET_REKEY_OFFLOAD: This command is used give the driver
+ *	the necessary information for supporting GTK rekey offload. This
+ *	feature is typically used during WoWLAN. The configuration data
+ *	is contained in %NL80211_ATTR_REKEY_DATA (which is nested and
+ *	contains the data in sub-attributes). After rekeying happened,
+ *	this command may also be sent by the driver as an MLME event to
+ *	inform userspace of the new replay counter.
+ *
  * @NL80211_CMD_MAX: highest used command number
  * @__NL80211_CMD_AFTER_LAST: internal use
  */
 enum nl80211_commands {
-/* don't change the order or add anything inbetween, this is ABI! */
+/* don't change the order or add anything between, this is ABI! */
 	NL80211_CMD_UNSPEC,
 
 	NL80211_CMD_GET_WIPHY,		/* can dump */
@@ -448,8 +534,8 @@ enum nl80211_commands {
 	NL80211_CMD_SET_REG,
 	NL80211_CMD_REQ_SET_REG,
 
-	NL80211_CMD_GET_MESH_PARAMS,
+	NL80211_CMD_GET_MESH_CONFIG,
-	NL80211_CMD_SET_MESH_PARAMS,
+	NL80211_CMD_SET_MESH_CONFIG,
 
 	NL80211_CMD_SET_MGMT_EXTRA_IE /* reserved; not used */,
 
@@ -518,6 +604,18 @@ enum nl80211_commands {
 	NL80211_CMD_UNPROT_DEAUTHENTICATE,
 	NL80211_CMD_UNPROT_DISASSOCIATE,
 
+	NL80211_CMD_NEW_PEER_CANDIDATE,
+
+	NL80211_CMD_GET_WOWLAN,
+	NL80211_CMD_SET_WOWLAN,
+
+	NL80211_CMD_START_SCHED_SCAN,
+	NL80211_CMD_STOP_SCHED_SCAN,
+	NL80211_CMD_SCHED_SCAN_RESULTS,
+	NL80211_CMD_SCHED_SCAN_STOPPED,
+
+	NL80211_CMD_SET_REKEY_OFFLOAD,
+
 	/* add new commands above here */
 
 	/* used to define NL80211_CMD_MAX below */
@@ -538,6 +636,11 @@ enum nl80211_commands {
 #define NL80211_CMD_DISASSOCIATE NL80211_CMD_DISASSOCIATE
 #define NL80211_CMD_REG_BEACON_HINT NL80211_CMD_REG_BEACON_HINT
 
+/* source-level API compatibility */
+#define NL80211_CMD_GET_MESH_PARAMS NL80211_CMD_GET_MESH_CONFIG
+#define NL80211_CMD_SET_MESH_PARAMS NL80211_CMD_SET_MESH_CONFIG
+#define NL80211_MESH_SETUP_VENDOR_PATH_SEL_IE NL80211_MESH_SETUP_IE
+
 /**
  * enum nl80211_attrs - nl80211 netlink attributes
  *
@@ -608,7 +711,7 @@ enum nl80211_commands {
  *	consisting of a nested array.
  *
  * @NL80211_ATTR_MESH_ID: mesh id (1-32 bytes).
- * @NL80211_ATTR_PLINK_ACTION: action to perform on the mesh peer link.
+ * @NL80211_ATTR_STA_PLINK_ACTION: action to perform on the mesh peer link.
  * @NL80211_ATTR_MPATH_NEXT_HOP: MAC address of the next hop for a mesh path.
  * @NL80211_ATTR_MPATH_INFO: information about a mesh_path, part of mesh path
  * 	info given for %NL80211_CMD_GET_MPATH, nested attribute described at
@@ -852,7 +955,13 @@ enum nl80211_commands {
  *	This can be used to mask out antennas which are not attached or should
  *	not be used for receiving. If an antenna is not selected in this bitmap
  *	the hardware should not be configured to receive on this antenna.
- *	For a more detailed descripton see @NL80211_ATTR_WIPHY_ANTENNA_TX.
+ *	For a more detailed description see @NL80211_ATTR_WIPHY_ANTENNA_TX.
+ *
+ * @NL80211_ATTR_WIPHY_ANTENNA_AVAIL_TX: Bitmap of antennas which are available
+ *	for configuration as TX antennas via the above parameters.
+ *
+ * @NL80211_ATTR_WIPHY_ANTENNA_AVAIL_RX: Bitmap of antennas which are available
+ *	for configuration as RX antennas via the above parameters.
  *
  * @NL80211_ATTR_MCAST_RATE: Multicast tx rate (in 100 kbps) for IBSS
  *
@@ -868,11 +977,44 @@ enum nl80211_commands {
  *	attributes, specifying what a key should be set as default as.
  *	See &enum nl80211_key_default_types.
  *
+ * @NL80211_ATTR_MESH_SETUP: Optional mesh setup parameters.  These cannot be
+ *	changed once the mesh is active.
+ * @NL80211_ATTR_MESH_CONFIG: Mesh configuration parameters, a nested attribute
+ *	containing attributes from &enum nl80211_meshconf_params.
+ * @NL80211_ATTR_SUPPORT_MESH_AUTH: Currently, this means the underlying driver
+ *	allows auth frames in a mesh to be passed to userspace for processing via
+ *	the @NL80211_MESH_SETUP_USERSPACE_AUTH flag.
+ * @NL80211_ATTR_STA_PLINK_STATE: The state of a mesh peer link as
+ *	defined in &enum nl80211_plink_state. Used when userspace is
+ *	driving the peer link management state machine.
+ *	@NL80211_MESH_SETUP_USERSPACE_AMPE must be enabled.
+ *
+ * @NL80211_ATTR_WOWLAN_SUPPORTED: indicates, as part of the wiphy capabilities,
+ *	the supported WoWLAN triggers
+ * @NL80211_ATTR_WOWLAN_TRIGGERS: used by %NL80211_CMD_SET_WOWLAN to
+ *	indicate which WoW triggers should be enabled. This is also
+ *	used by %NL80211_CMD_GET_WOWLAN to get the currently enabled WoWLAN
+ *	triggers.
+
+ * @NL80211_ATTR_SCHED_SCAN_INTERVAL: Interval between scheduled scan
+ *	cycles, in msecs.
+ *
+ * @NL80211_ATTR_INTERFACE_COMBINATIONS: Nested attribute listing the supported
+ *	interface combinations. In each nested item, it contains attributes
+ *	defined in &enum nl80211_if_combination_attrs.
+ * @NL80211_ATTR_SOFTWARE_IFTYPES: Nested attribute (just like
+ *	%NL80211_ATTR_SUPPORTED_IFTYPES) containing the interface types that
+ *	are managed in software: interfaces of these types aren't subject to
+ *	any restrictions in their number or combinations.
+ *
+ * @%NL80211_ATTR_REKEY_DATA: nested attribute containing the information
+ *	necessary for GTK rekeying in the device, see &enum nl80211_rekey_data.
+ *
  * @NL80211_ATTR_MAX: highest attribute number currently defined
  * @__NL80211_ATTR_AFTER_LAST: internal use
  */
 enum nl80211_attrs {
-/* don't change the order or add anything inbetween, this is ABI! */
+/* don't change the order or add anything between, this is ABI! */
 	NL80211_ATTR_UNSPEC,
 
 	NL80211_ATTR_WIPHY,
@@ -922,7 +1064,7 @@ enum nl80211_attrs {
 	NL80211_ATTR_REG_ALPHA2,
 	NL80211_ATTR_REG_RULES,
 
-	NL80211_ATTR_MESH_PARAMS,
+	NL80211_ATTR_MESH_CONFIG,
 
 	NL80211_ATTR_BSS_BASIC_RATES,
 
@@ -1050,6 +1192,24 @@ enum nl80211_attrs {
 
 	NL80211_ATTR_MAX_REMAIN_ON_CHANNEL_DURATION,
 
+	NL80211_ATTR_MESH_SETUP,
+
+	NL80211_ATTR_WIPHY_ANTENNA_AVAIL_TX,
+	NL80211_ATTR_WIPHY_ANTENNA_AVAIL_RX,
+
+	NL80211_ATTR_SUPPORT_MESH_AUTH,
+	NL80211_ATTR_STA_PLINK_STATE,
+
+	NL80211_ATTR_WOWLAN_TRIGGERS,
+	NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED,
+
+	NL80211_ATTR_SCHED_SCAN_INTERVAL,
+
+	NL80211_ATTR_INTERFACE_COMBINATIONS,
+	NL80211_ATTR_SOFTWARE_IFTYPES,
+
+	NL80211_ATTR_REKEY_DATA,
+
 	/* add attributes here, update the policy in nl80211.c */
 
 	__NL80211_ATTR_AFTER_LAST,
@@ -1058,6 +1218,7 @@ enum nl80211_attrs {
 
 /* source-level API compatibility */
 #define NL80211_ATTR_SCAN_GENERATION NL80211_ATTR_GENERATION
+#define	NL80211_ATTR_MESH_PARAMS NL80211_ATTR_MESH_CONFIG
 
 /*
  * Allow user space programs to use #ifdef on new attributes by defining them
@@ -1101,7 +1262,9 @@ enum nl80211_attrs {
  * @NL80211_IFTYPE_ADHOC: independent BSS member
  * @NL80211_IFTYPE_STATION: managed BSS member
  * @NL80211_IFTYPE_AP: access point
- * @NL80211_IFTYPE_AP_VLAN: VLAN interface for access points
+ * @NL80211_IFTYPE_AP_VLAN: VLAN interface for access points; VLAN interfaces
+ *	are a bit special in that they must always be tied to a pre-existing
+ *	AP type interface.
  * @NL80211_IFTYPE_WDS: wireless distribution interface
  * @NL80211_IFTYPE_MONITOR: monitor interface receiving all frames
  * @NL80211_IFTYPE_MESH_POINT: mesh point
@@ -1143,6 +1306,7 @@ enum nl80211_iftype {
  *	with short barker preamble
  * @NL80211_STA_FLAG_WME: station is WME/QoS capable
  * @NL80211_STA_FLAG_MFP: station uses management frame protection
+ * @NL80211_STA_FLAG_AUTHENTICATED: station is authenticated
  * @NL80211_STA_FLAG_MAX: highest station flag number currently defined
  * @__NL80211_STA_FLAG_AFTER_LAST: internal use
  */
@@ -1152,6 +1316,7 @@ enum nl80211_sta_flags {
 	NL80211_STA_FLAG_SHORT_PREAMBLE,
 	NL80211_STA_FLAG_WME,
 	NL80211_STA_FLAG_MFP,
+	NL80211_STA_FLAG_AUTHENTICATED,
 
 	/* keep last */
 	__NL80211_STA_FLAG_AFTER_LAST,
@@ -1196,6 +1361,36 @@ enum nl80211_rate_info {
 	NL80211_RATE_INFO_MAX = __NL80211_RATE_INFO_AFTER_LAST - 1
 };
 
+/**
+ * enum nl80211_sta_bss_param - BSS information collected by STA
+ *
+ * These attribute types are used with %NL80211_STA_INFO_BSS_PARAM
+ * when getting information about the bitrate of a station.
+ *
+ * @__NL80211_STA_BSS_PARAM_INVALID: attribute number 0 is reserved
+ * @NL80211_STA_BSS_PARAM_CTS_PROT: whether CTS protection is enabled (flag)
+ * @NL80211_STA_BSS_PARAM_SHORT_PREAMBLE:  whether short preamble is enabled
+ *	(flag)
+ * @NL80211_STA_BSS_PARAM_SHORT_SLOT_TIME:  whether short slot time is enabled
+ *	(flag)
+ * @NL80211_STA_BSS_PARAM_DTIM_PERIOD: DTIM period for beaconing (u8)
+ * @NL80211_STA_BSS_PARAM_BEACON_INTERVAL: Beacon interval (u16)
+ * @NL80211_STA_BSS_PARAM_MAX: highest sta_bss_param number currently defined
+ * @__NL80211_STA_BSS_PARAM_AFTER_LAST: internal use
+ */
+enum nl80211_sta_bss_param {
+	__NL80211_STA_BSS_PARAM_INVALID,
+	NL80211_STA_BSS_PARAM_CTS_PROT,
+	NL80211_STA_BSS_PARAM_SHORT_PREAMBLE,
+	NL80211_STA_BSS_PARAM_SHORT_SLOT_TIME,
+	NL80211_STA_BSS_PARAM_DTIM_PERIOD,
+	NL80211_STA_BSS_PARAM_BEACON_INTERVAL,
+
+	/* keep last */
+	__NL80211_STA_BSS_PARAM_AFTER_LAST,
+	NL80211_STA_BSS_PARAM_MAX = __NL80211_STA_BSS_PARAM_AFTER_LAST - 1
+};
+
 /**
  * enum nl80211_sta_info - station information
  *
@@ -1206,17 +1401,26 @@ enum nl80211_rate_info {
  * @NL80211_STA_INFO_INACTIVE_TIME: time since last activity (u32, msecs)
  * @NL80211_STA_INFO_RX_BYTES: total received bytes (u32, from this station)
  * @NL80211_STA_INFO_TX_BYTES: total transmitted bytes (u32, to this station)
- * @__NL80211_STA_INFO_AFTER_LAST: internal
- * @NL80211_STA_INFO_MAX: highest possible station info attribute
  * @NL80211_STA_INFO_SIGNAL: signal strength of last received PPDU (u8, dBm)
  * @NL80211_STA_INFO_TX_BITRATE: current unicast tx rate, nested attribute
- * 	containing info as possible, see &enum nl80211_sta_info_txrate.
+ * 	containing info as possible, see &enum nl80211_rate_info
  * @NL80211_STA_INFO_RX_PACKETS: total received packet (u32, from this station)
  * @NL80211_STA_INFO_TX_PACKETS: total transmitted packets (u32, to this
  *	station)
  * @NL80211_STA_INFO_TX_RETRIES: total retries (u32, to this station)
  * @NL80211_STA_INFO_TX_FAILED: total failed packets (u32, to this station)
  * @NL80211_STA_INFO_SIGNAL_AVG: signal strength average (u8, dBm)
+ * @NL80211_STA_INFO_LLID: the station's mesh LLID
+ * @NL80211_STA_INFO_PLID: the station's mesh PLID
+ * @NL80211_STA_INFO_PLINK_STATE: peer link state for the station
+ *	(see %enum nl80211_plink_state)
+ * @NL80211_STA_INFO_RX_BITRATE: last unicast data frame rx rate, nested
+ *	attribute, like NL80211_STA_INFO_TX_BITRATE.
+ * @NL80211_STA_INFO_BSS_PARAM: current station's view of BSS, nested attribute
+ *     containing info as possible, see &enum nl80211_sta_bss_param
+ * @NL80211_STA_INFO_CONNECTED_TIME: time since the station is last connected
+ * @__NL80211_STA_INFO_AFTER_LAST: internal
+ * @NL80211_STA_INFO_MAX: highest possible station info attribute
  */
 enum nl80211_sta_info {
 	__NL80211_STA_INFO_INVALID,
@@ -1233,6 +1437,9 @@ enum nl80211_sta_info {
 	NL80211_STA_INFO_TX_RETRIES,
 	NL80211_STA_INFO_TX_FAILED,
 	NL80211_STA_INFO_SIGNAL_AVG,
+	NL80211_STA_INFO_RX_BITRATE,
+	NL80211_STA_INFO_BSS_PARAM,
+	NL80211_STA_INFO_CONNECTED_TIME,
 
 	/* keep last */
 	__NL80211_STA_INFO_AFTER_LAST,
@@ -1388,7 +1595,7 @@ enum nl80211_bitrate_attr {
  * 	802.11 country information element with regulatory information it
  * 	thinks we should consider. cfg80211 only processes the country
  *	code from the IE, and relies on the regulatory domain information
- *	structure pased by userspace (CRDA) from our wireless-regdb.
+ *	structure passed by userspace (CRDA) from our wireless-regdb.
  *	If a channel is enabled but the country code indicates it should
  *	be disabled we disable the channel and re-enable it upon disassociation.
  */
@@ -1559,14 +1766,15 @@ enum nl80211_mntr_flags {
 /**
  * enum nl80211_meshconf_params - mesh configuration parameters
  *
- * Mesh configuration parameters
+ * Mesh configuration parameters. These can be changed while the mesh is
+ * active.
  *
  * @__NL80211_MESHCONF_INVALID: internal use
  *
  * @NL80211_MESHCONF_RETRY_TIMEOUT: specifies the initial retry timeout in
  * millisecond units, used by the Peer Link Open message
  *
- * @NL80211_MESHCONF_CONFIRM_TIMEOUT: specifies the inital confirm timeout, in
+ * @NL80211_MESHCONF_CONFIRM_TIMEOUT: specifies the initial confirm timeout, in
  * millisecond units, used by the peer link management to close a peer link
  *
  * @NL80211_MESHCONF_HOLDING_TIMEOUT: specifies the holding timeout, in
@@ -1582,9 +1790,6 @@ enum nl80211_mntr_flags {
  * @NL80211_MESHCONF_TTL: specifies the value of TTL field set at a source mesh
  * point.
  *
- * @NL80211_MESHCONF_ELEMENT_TTL: specifies the value of TTL field set at a
- * source mesh point for path selection elements.
- *
  * @NL80211_MESHCONF_AUTO_OPEN_PLINKS: whether we should automatically
  * open peer links when we detect compatible mesh peers.
  *
@@ -1609,7 +1814,10 @@ enum nl80211_mntr_flags {
  * @NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME: The interval of time (in TUs)
  * that it takes for an HWMP information element to propagate across the mesh
  *
- * @NL80211_MESHCONF_ROOTMODE: whether root mode is enabled or not
+ * @NL80211_MESHCONF_HWMP_ROOTMODE: whether root mode is enabled or not
+ *
+ * @NL80211_MESHCONF_ELEMENT_TTL: specifies the value of TTL field set at a
+ * source mesh point for path selection elements.
  *
  * @NL80211_MESHCONF_ATTR_MAX: highest possible mesh configuration attribute
  *
@@ -1638,6 +1846,54 @@ enum nl80211_meshconf_params {
 	NL80211_MESHCONF_ATTR_MAX = __NL80211_MESHCONF_ATTR_AFTER_LAST - 1
 };
 
+/**
+ * enum nl80211_mesh_setup_params - mesh setup parameters
+ *
+ * Mesh setup parameters.  These are used to start/join a mesh and cannot be
+ * changed while the mesh is active.
+ *
+ * @__NL80211_MESH_SETUP_INVALID: Internal use
+ *
+ * @NL80211_MESH_SETUP_ENABLE_VENDOR_PATH_SEL: Enable this option to use a
+ * vendor specific path selection algorithm or disable it to use the default
+ * HWMP.
+ *
+ * @NL80211_MESH_SETUP_ENABLE_VENDOR_METRIC: Enable this option to use a
+ * vendor specific path metric or disable it to use the default Airtime
+ * metric.
+ *
+ * @NL80211_MESH_SETUP_IE: Information elements for this mesh, for instance, a
+ * robust security network ie, or a vendor specific information element that
+ * vendors will use to identify the path selection methods and metrics in use.
+ *
+ * @NL80211_MESH_SETUP_USERSPACE_AUTH: Enable this option if an authentication
+ * daemon will be authenticating mesh candidates.
+ *
+ * @NL80211_MESH_SETUP_USERSPACE_AMPE: Enable this option if an authentication
+ * daemon will be securing peer link frames.  AMPE is a secured version of Mesh
+ * Peering Management (MPM) and is implemented with the assistance of a
+ * userspace daemon.  When this flag is set, the kernel will send peer
+ * management frames to a userspace daemon that will implement AMPE
+ * functionality (security capabilities selection, key confirmation, and key
+ * management).  When the flag is unset (default), the kernel can autonomously
+ * complete (unsecured) mesh peering without the need of a userspace daemon.
+ *
+ * @NL80211_MESH_SETUP_ATTR_MAX: highest possible mesh setup attribute number
+ * @__NL80211_MESH_SETUP_ATTR_AFTER_LAST: Internal use
+ */
+enum nl80211_mesh_setup_params {
+	__NL80211_MESH_SETUP_INVALID,
+	NL80211_MESH_SETUP_ENABLE_VENDOR_PATH_SEL,
+	NL80211_MESH_SETUP_ENABLE_VENDOR_METRIC,
+	NL80211_MESH_SETUP_IE,
+	NL80211_MESH_SETUP_USERSPACE_AUTH,
+	NL80211_MESH_SETUP_USERSPACE_AMPE,
+
+	/* keep last */
+	__NL80211_MESH_SETUP_ATTR_AFTER_LAST,
+	NL80211_MESH_SETUP_ATTR_MAX = __NL80211_MESH_SETUP_ATTR_AFTER_LAST - 1
+};
+
 /**
  * enum nl80211_txq_attr - TX queue parameter attributes
  * @__NL80211_TXQ_ATTR_INVALID: Attribute number 0 is reserved
@@ -1936,4 +2192,213 @@ enum nl80211_tx_power_setting {
 	NL80211_TX_POWER_FIXED,
 };
 
+/**
+ * enum nl80211_wowlan_packet_pattern_attr - WoWLAN packet pattern attribute
+ * @__NL80211_WOWLAN_PKTPAT_INVALID: invalid number for nested attribute
+ * @NL80211_WOWLAN_PKTPAT_PATTERN: the pattern, values where the mask has
+ *	a zero bit are ignored
+ * @NL80211_WOWLAN_PKTPAT_MASK: pattern mask, must be long enough to have
+ *	a bit for each byte in the pattern. The lowest-order bit corresponds
+ *	to the first byte of the pattern, but the bytes of the pattern are
+ *	in a little-endian-like format, i.e. the 9th byte of the pattern
+ *	corresponds to the lowest-order bit in the second byte of the mask.
+ *	For example: The match 00:xx:00:00:xx:00:00:00:00:xx:xx:xx (where
+ *	xx indicates "don't care") would be represented by a pattern of
+ *	twelve zero bytes, and a mask of "0xed,0x07".
+ *	Note that the pattern matching is done as though frames were not
+ *	802.11 frames but 802.3 frames, i.e. the frame is fully unpacked
+ *	first (including SNAP header unpacking) and then matched.
+ * @NUM_NL80211_WOWLAN_PKTPAT: number of attributes
+ * @MAX_NL80211_WOWLAN_PKTPAT: max attribute number
+ */
+enum nl80211_wowlan_packet_pattern_attr {
+	__NL80211_WOWLAN_PKTPAT_INVALID,
+	NL80211_WOWLAN_PKTPAT_MASK,
+	NL80211_WOWLAN_PKTPAT_PATTERN,
+
+	NUM_NL80211_WOWLAN_PKTPAT,
+	MAX_NL80211_WOWLAN_PKTPAT = NUM_NL80211_WOWLAN_PKTPAT - 1,
+};
+
+/**
+ * struct nl80211_wowlan_pattern_support - pattern support information
+ * @max_patterns: maximum number of patterns supported
+ * @min_pattern_len: minimum length of each pattern
+ * @max_pattern_len: maximum length of each pattern
+ *
+ * This struct is carried in %NL80211_WOWLAN_TRIG_PKT_PATTERN when
+ * that is part of %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED in the
+ * capability information given by the kernel to userspace.
+ */
+struct nl80211_wowlan_pattern_support {
+	__u32 max_patterns;
+	__u32 min_pattern_len;
+	__u32 max_pattern_len;
+} __attribute__((packed));
+
+/**
+ * enum nl80211_wowlan_triggers - WoWLAN trigger definitions
+ * @__NL80211_WOWLAN_TRIG_INVALID: invalid number for nested attributes
+ * @NL80211_WOWLAN_TRIG_ANY: wake up on any activity, do not really put
+ *	the chip into a special state -- works best with chips that have
+ *	support for low-power operation already (flag)
+ * @NL80211_WOWLAN_TRIG_DISCONNECT: wake up on disconnect, the way disconnect
+ *	is detected is implementation-specific (flag)
+ * @NL80211_WOWLAN_TRIG_MAGIC_PKT: wake up on magic packet (6x 0xff, followed
+ *	by 16 repetitions of MAC addr, anywhere in payload) (flag)
+ * @NL80211_WOWLAN_TRIG_PKT_PATTERN: wake up on the specified packet patterns
+ *	which are passed in an array of nested attributes, each nested attribute
+ *	defining a with attributes from &struct nl80211_wowlan_trig_pkt_pattern.
+ *	Each pattern defines a wakeup packet. The matching is done on the MSDU,
+ *	i.e. as though the packet was an 802.3 packet, so the pattern matching
+ *	is done after the packet is converted to the MSDU.
+ *
+ *	In %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED, it is a binary attribute
+ *	carrying a &struct nl80211_wowlan_pattern_support.
+ * @NUM_NL80211_WOWLAN_TRIG: number of wake on wireless triggers
+ * @MAX_NL80211_WOWLAN_TRIG: highest wowlan trigger attribute number
+ */
+enum nl80211_wowlan_triggers {
+	__NL80211_WOWLAN_TRIG_INVALID,
+	NL80211_WOWLAN_TRIG_ANY,
+	NL80211_WOWLAN_TRIG_DISCONNECT,
+	NL80211_WOWLAN_TRIG_MAGIC_PKT,
+	NL80211_WOWLAN_TRIG_PKT_PATTERN,
+
+	/* keep last */
+	NUM_NL80211_WOWLAN_TRIG,
+	MAX_NL80211_WOWLAN_TRIG = NUM_NL80211_WOWLAN_TRIG - 1
+};
+
+/**
+ * enum nl80211_iface_limit_attrs - limit attributes
+ * @NL80211_IFACE_LIMIT_UNSPEC: (reserved)
+ * @NL80211_IFACE_LIMIT_MAX: maximum number of interfaces that
+ *	can be chosen from this set of interface types (u32)
+ * @NL80211_IFACE_LIMIT_TYPES: nested attribute containing a
+ *	flag attribute for each interface type in this set
+ * @NUM_NL80211_IFACE_LIMIT: number of attributes
+ * @MAX_NL80211_IFACE_LIMIT: highest attribute number
+ */
+enum nl80211_iface_limit_attrs {
+	NL80211_IFACE_LIMIT_UNSPEC,
+	NL80211_IFACE_LIMIT_MAX,
+	NL80211_IFACE_LIMIT_TYPES,
+
+	/* keep last */
+	NUM_NL80211_IFACE_LIMIT,
+	MAX_NL80211_IFACE_LIMIT = NUM_NL80211_IFACE_LIMIT - 1
+};
+
+/**
+ * enum nl80211_if_combination_attrs -- interface combination attributes
+ *
+ * @NL80211_IFACE_COMB_UNSPEC: (reserved)
+ * @NL80211_IFACE_COMB_LIMITS: Nested attributes containing the limits
+ *	for given interface types, see &enum nl80211_iface_limit_attrs.
+ * @NL80211_IFACE_COMB_MAXNUM: u32 attribute giving the total number of
+ *	interfaces that can be created in this group. This number doesn't
+ *	apply to interfaces purely managed in software, which are listed
+ *	in a separate attribute %NL80211_ATTR_INTERFACES_SOFTWARE.
+ * @NL80211_IFACE_COMB_STA_AP_BI_MATCH: flag attribute specifying that
+ *	beacon intervals within this group must be all the same even for
+ *	infrastructure and AP/GO combinations, i.e. the GO(s) must adopt
+ *	the infrastructure network's beacon interval.
+ * @NL80211_IFACE_COMB_NUM_CHANNELS: u32 attribute specifying how many
+ *	different channels may be used within this group.
+ * @NUM_NL80211_IFACE_COMB: number of attributes
+ * @MAX_NL80211_IFACE_COMB: highest attribute number
+ *
+ * Examples:
+ *	limits = [ #{STA} <= 1, #{AP} <= 1 ], matching BI, channels = 1, max = 2
+ *	=> allows an AP and a STA that must match BIs
+ *
+ *	numbers = [ #{AP, P2P-GO} <= 8 ], channels = 1, max = 8
+ *	=> allows 8 of AP/GO
+ *
+ *	numbers = [ #{STA} <= 2 ], channels = 2, max = 2
+ *	=> allows two STAs on different channels
+ *
+ *	numbers = [ #{STA} <= 1, #{P2P-client,P2P-GO} <= 3 ], max = 4
+ *	=> allows a STA plus three P2P interfaces
+ *
+ * The list of these four possiblities could completely be contained
+ * within the %NL80211_ATTR_INTERFACE_COMBINATIONS attribute to indicate
+ * that any of these groups must match.
+ *
+ * "Combinations" of just a single interface will not be listed here,
+ * a single interface of any valid interface type is assumed to always
+ * be possible by itself. This means that implicitly, for each valid
+ * interface type, the following group always exists:
+ *	numbers = [ #{<type>} <= 1 ], channels = 1, max = 1
+ */
+enum nl80211_if_combination_attrs {
+	NL80211_IFACE_COMB_UNSPEC,
+	NL80211_IFACE_COMB_LIMITS,
+	NL80211_IFACE_COMB_MAXNUM,
+	NL80211_IFACE_COMB_STA_AP_BI_MATCH,
+	NL80211_IFACE_COMB_NUM_CHANNELS,
+
+	/* keep last */
+	NUM_NL80211_IFACE_COMB,
+	MAX_NL80211_IFACE_COMB = NUM_NL80211_IFACE_COMB - 1
+};
+
+
+/**
+ * enum nl80211_plink_state - state of a mesh peer link finite state machine
+ *
+ * @NL80211_PLINK_LISTEN: initial state, considered the implicit
+ *	state of non existant mesh peer links
+ * @NL80211_PLINK_OPN_SNT: mesh plink open frame has been sent to
+ *	this mesh peer
+ * @NL80211_PLINK_OPN_RCVD: mesh plink open frame has been received
+ *	from this mesh peer
+ * @NL80211_PLINK_CNF_RCVD: mesh plink confirm frame has been
+ *	received from this mesh peer
+ * @NL80211_PLINK_ESTAB: mesh peer link is established
+ * @NL80211_PLINK_HOLDING: mesh peer link is being closed or cancelled
+ * @NL80211_PLINK_BLOCKED: all frames transmitted from this mesh
+ *	plink are discarded
+ * @NUM_NL80211_PLINK_STATES: number of peer link states
+ * @MAX_NL80211_PLINK_STATES: highest numerical value of plink states
+ */
+enum nl80211_plink_state {
+	NL80211_PLINK_LISTEN,
+	NL80211_PLINK_OPN_SNT,
+	NL80211_PLINK_OPN_RCVD,
+	NL80211_PLINK_CNF_RCVD,
+	NL80211_PLINK_ESTAB,
+	NL80211_PLINK_HOLDING,
+	NL80211_PLINK_BLOCKED,
+
+	/* keep last */
+	NUM_NL80211_PLINK_STATES,
+	MAX_NL80211_PLINK_STATES = NUM_NL80211_PLINK_STATES - 1
+};
+
+#define NL80211_KCK_LEN			16
+#define NL80211_KEK_LEN			16
+#define NL80211_REPLAY_CTR_LEN		8
+
+/**
+ * enum nl80211_rekey_data - attributes for GTK rekey offload
+ * @__NL80211_REKEY_DATA_INVALID: invalid number for nested attributes
+ * @NL80211_REKEY_DATA_KEK: key encryption key (binary)
+ * @NL80211_REKEY_DATA_KCK: key confirmation key (binary)
+ * @NL80211_REKEY_DATA_REPLAY_CTR: replay counter (binary)
+ * @NUM_NL80211_REKEY_DATA: number of rekey attributes (internal)
+ * @MAX_NL80211_REKEY_DATA: highest rekey attribute (internal)
+ */
+enum nl80211_rekey_data {
+	__NL80211_REKEY_DATA_INVALID,
+	NL80211_REKEY_DATA_KEK,
+	NL80211_REKEY_DATA_KCK,
+	NL80211_REKEY_DATA_REPLAY_CTR,
+
+	/* keep last */
+	NUM_NL80211_REKEY_DATA,
+	MAX_NL80211_REKEY_DATA = NUM_NL80211_REKEY_DATA - 1
+};
+
 #endif /* __LINUX_NL80211_H */